OEM Restraints System Part Replacement Search
2019 Jaguar I-PACE
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
1. Remove the ignition key.2. Disconnect battery, earth lead first.
3. Wait 2 minutes for the SRS power circuit to discharge before commencing work
REV: 10/2024
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
If the front airbags are deployed, the following components must be replaced:• Driver airbag module [AIRBAG,STEERING WHEEL]
• Passenger airbag module [AIRBAG,INSTRUMENT PNL]
• Fly leads (where applicable) connecting front airbag modules to SRS harness
• Front seat belt buckle pre-tensioner
• Rear seat belt pre-tensioners • if installed
• Driver's seat belt retractor • if installed
• Rotary coupler [CLOCK SPRING/LVR,STRG]
• Any front impact sensors that have been physically damaged or if a fault is being registered [AIRBAG SENSOR,FRONT]
• Restraints control module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]
If the side (thorax) air bags are deployed, the following components must be replaced on the side of the vehicle on which the deployment occurred:
• Side (thorax) airbag [AIRBAG,FRONT SEAT]
• Any side impact sensors that have been physically damaged or if a fault is being registered [AIRBAG SENSOR,SIDE; AIRBAG SENSOR,QTR PANEL]
• Restraints control module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]
If the head airbag modules are deployed, the following components must be replaced on the side of the vehicle on which the deployment occurred:
• Head airbag modules [AIRBAG,ROOF]
• Link lead between airbag gas generator and restraints control module (RCM) harness
• Airbag retaining clips
• Internal trim finisher
• Front seat belt buckle pre-tensioners
• Any side impact sensors that have been physically damaged or if a fault is being registered [AIRBAG SENSOR,SIDE; AIRBAG SENSOR,QTR PANEL]
• Restraints control module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]
If the seat belt pre-tensioners are deployed during a rear impact, the following components must be replaced:
• Seat belt pre-tensioners
• Front and rear seat belt retractors used during the impact
• Restraints control module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]
The Restraints Control Module (RCM) will log a crash fault after every impact which is severe enough to cause airbag deployment. It is possible to have three
crashes/impacts logged after one event where, for example, a front, side and rollover has occurred. After the third fault is logged, the SRS warning lamp will be
illuminated and the RCM must be installed. After any airbag deployment a new RCM must be installed [MODULE,AIRBAG CONTROL]
The SRS side impact sensor must be replaced if there are any signs of physical damage or if the restraints control module (RCM) is registering a fault [AIRBAG SENSOR,SIDE; AIRBAG SENSOR,QTR PANEL]
Always replace a seat belt assembly that has withstood the strain of a severe vehicle impact or if the webbing shows signs of fraying
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
If the front airbags are deployed • Additionally, the following items must be inspected for damage and replaced as necessary:• Front passenger's seat belt retractor and webbing, tongue latching function, 'D' loop and body anchorage point
• Rear seat belt buckles, webbing, buckle covers, body anchorage points and tongue latching function
• Fascia moulding adjacent to passenger airbag module
• Steering wheel
• Front seat frames and head restraints
• Steering column • if adjustment is lost or if there are signs of collapse
• Seat belt height adjusters
• Rear seat belts
If the side (thorax) air bags are deployed • Additionally, the following items must be inspected for damage and replaced as necessary:
• Front seat belts, retractors and webbing, tongue latching function, 'D' loop and body anchorage points
• Rear seat belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points
• Front seat frame and head restraints
• Door trim casing
• Seat belt height adjusters
• Rear seat belts
If the side (thorax) air bags are deployed • Additionally, the following items must be inspected for damage and replaced as necessary:
• Headlining
• Component mounting brackets
• Front seat belts, retractors and webbing, tongue latching function, 'D' loop and body anchorage points
• Rear seat belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points
• Adjacent trim components
• Seat belt height adjusters
If the seat belt pre-tensioners are deployed during a rear impact • Additionally, the following items must be inspected for damage and replaced as necessary:
• Seat belt height adjusters
• Front seat belts, retractors and webbing, tongue latching function, 'D' loop and body anchorage points
• Rear seat belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points
| Additional Information |