OEM Restraints System Part Replacement Search
2010 Acura RL
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
Before doing any SRS repairs, check the DTCs for the less obvious deployed components (seat belt tensioners, front impact sensors, side airbag sensors, etc.).Make sure you have the anti-theft code(s) for the audio system and/or the audio-navigation system (if equipped).
Before disconnecting the SRS unit connectors, always disconnect the appropriate SRS parts connectors.
1. Make sure the ignition switch is in LOCK (0), or the vehicle ignition in the OFF mode.
2. Disconnect and isolate the negative cable from the battery.
3. Wait at least 3 minutes before starting work
REV: 01/2011
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
After a collision where the seat belt tensioners deployed, replace these items:• SRS unit [MODULE,AIRBAG CONTROL]
• Seat belt tensioners
• If the seat belt tensioner has been deployed, replace the front seat belt protector with a new one.
• Front impact sensors [AIRBAG SENSOR,FRONT]
• Any damaged restraint system part
After a collision where the front airbag(s) deployed, replace these items:
• SRS unit [MODULE,AIRBAG CONTROL]
• Steering Wheel Mounted Airbag, If Deployed [AIRBAG,STEERING WHEEL]
• Instrument Panel Airbag, If Deployed [AIRBAG,INSTRUMENT PNL]
• Seat belt tensioners
• If the seat belt tensioner has been deployed, replace the front seat belt protector with a new one.
• Front impact sensors [AIRBAG SENSOR,FRONT]
• Dashboard, if the Instrument Panel Airbag deployed
• Any damaged restraint system part
After a collision where the side airbag(s) deployed, replace the items for the side(s) that deployed:
• SRS unit [MODULE,AIRBAG CONTROL]
• Drivers side seat airbag [AIRBAG,FRONT SEAT], if deployed
• Passenger's side seat airbag [AIRBAG,FRONT SEAT], if deployed
• If you are replacing a deployed airbag, replace the airbag attachment wire
• After a collision where the side seat airbag was deployed, replace the seat-back cover and side seat airbag with new parts. If the seat-back cushion is split, it must be replaced. If the seat-back frame is deformed, it must be replaced.
• Side impact sensor(s) (first) for the side(s) that deployed [AIRBAG SENSOR,SIDE]
• Side impact sensor(s) (second) for the side(s) that deployed [AIRBAG SENSOR,QTR PANEL]
• B-pillar lower trim
• Any damaged restraint system part
After a collision where a side curtain airbag has deployed, replace the items for the side(s) that deployed:
• SRS unit [MODULE,AIRBAG CONTROL]
• Left side curtain airbag [AIRBAG,ROOF], if deployed
• Right side curtain airbag [AIRBAG,ROOF], if deployed
• Seat belt tensioner(s) for the side(s) that deployed
• If the seat belt tensioner has been deployed, replace the front seat belt protector with a new one.
• Side impact sensor(s) (first) for the side(s) that deployed [AIRBAG SENSOR,SIDE]
• Side impact sensor(s) (second) for the side(s) that deployed [AIRBAG SENSOR,QTR PANEL]
• Rear safing sensor [AIRBAG SENSOR,INTERIOR]
• Roof trim/ Headliner
• A pillar trim
• B pillar trim
• C-pillar trim
• Front grab handle
• Rear grab handle
• All related trim clips
• Sunvisor
• Any damaged restraint system part
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
• After a vehicle collision, do the ODS unit operation check• ODS Unit; Do not replace the ODS unit unless it is physically damaged or a specific fault was found during DTC troubleshooting
• After a vehicle collision, inspect the front seat active head restraints
• Inspect all the SRS wire harnesses. Replace, do not repair, any damaged harnesses
• Inspect the cable reel for heat damage. If there is any damage, replace the cable reel [CLOCK SPRING]
• Seatbelts and seatbelt mounting points
• Seats and seat mounting points
• After a moderate to severe side or rear collision, inspect for any damage on the side curtain airbag or other related components. If the airbag is frayed, or has any other visible damage, replace it. Do not attempt to repair an airbag. If the clips are stress-whitened, replace them with new ones.
• Front Passenger's Weight Sensor inspection procedure
• Any restraint system part or wiring identified by diagnostic check
| Additional Information |