PrintDISABLE PROCEDURE AND TIME (Always Check Service Manual)
1. Remove the ignition key.2. Disconnect battery, negative lead first.
3. Wait 2 minutes for the SRS power circuit to discharge before commencing work.
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
Safety belt pre-tensioner deployment:• Safety belt pre-tensioners
• Front and rear safety belt retractors deployed during the impact
• Restraints control module (RCM) if the three crashes/impacts have been stored
• Any restraint system part (brackets and fixings) or wiring identified by diagnostic check
For front airbag deployment:
• Driver airbag module (if deployed)
• Passenger airbag module (if deployed)
• Flyleads (where applicable) connecting front airbag modules to SRS harness
• Front seat belt buckle pre-tensioner
• Rear seat belt pre-tensioner • if installed
• Driver seat belt retractor • if installed
• Rotary coupler(clockspring)
• Any front impact sensors that have been physically damaged or if a fault is being registered
• Restraints control module (RCM) if the three crashes/impacts have been stored
• Any restraint system part, bracket or wiring identified by diagnostic check
For a side (thorax) airbag deployment:
• Side (thorax) airbag (if deployed)
• Any side impact sensors that have been physically damaged or if a fault is being registered
• Restraints control module (RCM) if the three crashes/impacts have been stored
• Any restraint system part, bracket or wiring identified by diagnostic check
For a head airbag module deployment:
• Head airbag modules (if deployed)
• Link lead between airbag gas generator and restraints control module (RCM) harness
• Airbag retaining clips
• Internal trim finisher
• Front seat belt buckle pre-tensioners
• Any side impact sensors that have been physically damaged or if a fault is being registered
• Restraints control module (RCM) if the three crashes/impacts have been stored
• Any restraint system part, bracket or wiring identified by diagnostic check
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
Safety belt pre-tensioner deployment:• Safety belt height adjusters
• Front safety belts, retractors and webbing, tongue latching function, and body anchorage points
• Rear safety belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points
• Bumper armatures, longitudinals and bracketry (structural damage)
• Any restraint system part, bracket or wiring identified by diagnostic check
For a front airbag deployment:
• Front passenger's seat belt retractor and webbing, tongue latching function, 'D' loop, body anchorage point
• Rear seat seat buckles • webbing, buckle covers, tongue latching function, body anchorage points
• Fascia moulding adjacent to passenger airbag module
• Steering wheel
• Front seat frames and head restraints
• Steering column • if adjustment is lost or if there are signs of collapse, replace
• Seat belt height adjusters
• Rear seat belts
• Bumper armatures, longitudinals and bracketry (structural damage)
• Any restraint system part, bracket or wiring identified by diagnostic check
For a side (thorax) airbag deployment:
• Front seat belts, retractors, webbing, tongue latching function, 'D' loop, body anchorage points
• Rear seat belt buckles, webbing, buckle covers, tongue latching function, body anchorage points
• Front seat frame and head restraints
• Door trim casing
• Seat belt height adjusters
• Rear seat belts
• Bumper armatures, longitudinals and bracketry (structural damage)
• Any restraint system part, bracket or wiring identified by diagnostic check
For a head airbag module deployment:
• • Headlining
• Component mounting brackets
• Front seat belts, retractors, webbing, tongue latching function, 'D' loop, body anchorage points
• Rear seat belt buckles, webbing, buckle covers, tongue latching function and body anchorage points
• Adjacent trim components
• Seat belt height adjusters
• Bumper armatures, longitudinals and bracketry (structural damage)
• Any restraint system part, bracket or wiring identified by diagnostic check