PrintDISABLE PROCEDURE AND TIME (Always Check Service Manual)
1. Remove the ignition key.2. Disconnect the battery, earth lead first.
3. Allow a period of 10 minutes to elapse after disconnecting the battery before undertaking any work on the SRS.
REV: 06/2022
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
The replacement and inspection policy is dependent on the type and severity of the crash condition. The following guidelines are the minimum that should be exercised as a result of the deployment of specific SRS components:Always use new fixings when replacing an SRS component
If the front air bags are deployed, the following components must be replaced:
• Driver air bag module, if deployed [AIRBAG,STEERING WHEEL]
• Passenger air bag module, if deployed [AIRBAG,INSTRUMENT PNL]
• Fly leads (where applicable) connecting front air bag modules to SRS harness
• Front seat belt buckle pre-tensioner, if deployed
• Rear seat belt pre-tensioners • if installed
• Driver's seat belt retractor • if installed
• Clockspring
• Any front impact sensors that have been physically damaged or if a fault is being registered [AIRBAG SENSOR,FRONT]
• Restraints Control Module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]
If the side air curtains are deployed, the following components must be replaced on the side of the vehicle on which the deployment occurred:
• Side air curtains if deployed [AIRBAG,FRONT SEAT]
• Any side impact sensors that have been physically damaged or if a fault is being registered [AIRBAG SENSOR,FRT DOOR; AIRBAG SENSOR,SIDE; AIRBAG SENSOR,QTR PANEL]
• Restraints Control Module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]
If the Side Air Curtain modules are deployed, the following components must be replaced on the side of the vehicle on which the deployment occurred:
• Side Air Curtain modules [AIRBAG,ROOF]
• Link lead between side air curtain gas generator and restraints control module (RCM) harness
• Side air curtain module retaining clips
• Internal trim finisher
• Front seat belt buckle pre-tensioners
• Any side impact sensors that have been physically damaged or if a fault is being registered [AIRBAG SENSOR,FRT DOOR; AIRBAG SENSOR,SIDE; AIRBAG SENSOR,QTR PANEL]
• Restraints Control Module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]
If the seat belt pre-tensioners are deployed during a rear impact, the following components must be replaced:
• Seat belt pre-tensioners
• Front and rear safety belt retractors deployed during the impact
• Restraints Control Module (RCM) if the three crashes/impacts have been stored [MODULE,AIRBAG CONTROL]
Always replace a safety belt assembly that has withstood the strain of a severe vehicle impact or if the webbing shows signs of fraying.
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
• Check for structural damage in the area of impact paying particular attention to bumper armatures, longitudinals and bracketry.• Always replace a seat belt assembly that has withstood the strain of a severe vehicle impact or if the webbing shows signs of fraying.
• Always use new fixings when replacing an SRS component
If the front air bags are deployed, the following items must be inspected for damage and replaced as necessary:
• Front passenger safety belt retractor and webbing, tongue latching function, 'D' loop and body anchorage point
• Rear seat belt buckles, webbing, buckle covers, body anchorage points and tongue latching function
• Instrument panel moulding adjacent to passenger air bag module
• Steering wheel
• Front seat frames and head restraints
• Steering column • if adjustment is lost or if there are signs of collapse
• Seat belt height adjusters
• Rear seat belts
If the Side (thorax) airbag [AIRBAG,FRONT SEAT] are deployed, the following items must be inspected for damage and replaced as necessary:
• Front seat belts, retractors and webbing, tongue latching function, 'D' loop and body anchorage points
• Rear seat belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points
• Front seat frame and head restraints
• Door trim casing
• Seat belt height adjusters
• Rear seat belts
If the Head airbag modules [AIRBAG,ROOF] are deployed, the following items must be inspected for damage and replaced as necessary:
• Headlining
• Component mounting brackets
• Front safety belts, retractors and webbing, tongue latching function, 'D' loop and body anchorage points
• Rear seat belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points
• Adjacent trim components
• Safety belt height adjusters
If the seat belt pre-tensioners are deployed during a rear impact, the following items must be inspected for damage and replaced as necessary:
• Seat belt height adjusters
• Front safety belts, retractors and webbing, tongue latching function, 'D' loop and body anchorage points
• Rear safety belt buckles, webbing, buckle covers, tongue latching function, and body anchorage points
Never attempt to modify, splice or repair SRS wiring