OEM Calibration Requirements Search
2019 Hyundai Sonata Plug-in Hybrid
Click the links below for directions; definitions; articles; and additional RTS portal information such as OEM position statements and publications.
Camera in Deck Lid/Liftgate/Tailgate
OEM Name: Back View Camera
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Camera in Deck Lid/Liftgate/Tailgate | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Deck Lid/Liftgate/Tailgate (Middle)
OEM Name: Rear Pantoscopic Camera
Calibration/Initialization Requirement Events:
- If camera is removed/installed or replaced
- If conducting a body task, such as the trunk task, that causes the focus of the wide camera to change
- If door mirror is replaced
- If surround view monitoring unit is replaced
| Camera in Deck Lid/Liftgate/Tailgate (Middle) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Front Bumper Cover/Grille
OEM Name: Front Pantoscopic Camera
Calibration/Initialization Requirement Events:
- If camera is removed/installed or replaced
- If conducting a body task, such as the trunk task, that causes the focus of the wide camera to change
- If door mirror is replaced
- If surround view monitoring unit is replaced
| Camera in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Left)
OEM Name: Left/Right Pantoscopic Camera
Calibration/Initialization Requirement Events:
- If around view monitoring unit is replaced
- If camera is removed/installed or replaced
- If conducting a body task, such as the trunk task, that causes the focus of the wide camera to change
- If door mirror is replaced
| Camera in Side Mirror (Left) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Right)
OEM Name: Left/Right Pantoscopic Camera
Calibration/Initialization Requirement Events:
- If camera is removed/installed or replaced
- If conducting a body task, such as the trunk task, that causes the focus of the wide camera to change
- If door mirror is replaced
- If surround view monitoring unit is replaced
| Camera in Side Mirror (Right) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera Near Rearview Mirror
OEM Name: Front View Camera
Calibration/Initialization Requirement Events:
- If camera bracket is damaged
- If camera is removed/installed or replaced
- If windshield is replaced
| Camera Near Rearview Mirror | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Note:
After replacing the camera with a new one, the variant coding procedure must be performed.
Sensor(s) Behind Front Bumper Cover/Grille
OEM Name: Smart Cruise Control Sensor
Calibration/Initialization Requirement Events:
- If sensor does not detect a vehicle in front
- If sensor is removed/installed or replaced
- If sensor or nearby parts are impacted in a collision
- If steering angle sensor is replaced or adjusted
- If vehicle has an accident with structural damage that requires a wheel alignment
| Sensor(s) Behind Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Note:
After replacing the sensor with a new one, the variant coding procedure must be performed.
Sensor(s) Behind Rear Bumper Cover (Sides)
OEM Name: Blind Spot Collision Warning Unit
Calibration/Initialization Requirement Events:
- If sensor bracket is replaced
- If sensor is replaced
- If vehicle has a rear bumper accident
| Sensor(s) Behind Rear Bumper Cover (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Additional Location(s)
OEM Name: Auto Head Lamp Leveling Unit
Calibration/Initialization Requirement Events:
- If AHLDM module is replaced
- If height sensor is replaced
| Sensor(s) in Additional Location(s) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Rear Bumper Cover
OEM Name: Parking Assist Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Rear Bumper Cover | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
| Additional Information | |