OEM Calibration Requirements Search
2019 Nissan Rogue
Click the links below for directions; definitions; articles; and additional RTS portal information such as OEM position statements and publications.
Camera in Deck Lid/Liftgate/Tailgate (Rear View Only)
OEM Name: Rear View Camera
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Camera in Deck Lid/Liftgate/Tailgate (Rear View Only) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Deck Lid/Liftgate/Tailgate (With 360° View)
OEM Name: Rear Camera
Calibration/Initialization Requirement Events:
- If any 360° camera or body component that camera is attached to is removed or replaced
- If around view monitor control unit is replaced
| Camera in Deck Lid/Liftgate/Tailgate (With 360° View) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Front Bumper Cover/Grille
OEM Name: Front Camera
Calibration/Initialization Requirement Events:
- If any 360° camera or body component that camera is attached to is removed or replaced
- If around view monitor control unit is replaced
| Camera in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Left)
OEM Name: Side Camera
Calibration/Initialization Requirement Events:
- If any 360° camera or body component that camera is attached to is removed or replaced
- If around view monitor control unit is replaced
| Camera in Side Mirror (Left) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Right)
OEM Name: Side Camera
Calibration/Initialization Requirement Events:
- If any 360° camera or body component that camera is attached to is removed or replaced
- If around view monitor control unit is replaced
| Camera in Side Mirror (Right) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera Near Rearview Mirror
OEM Name: Lane Camera Unit
Calibration/Initialization Requirement Events:
- If camera is removed or replaced
- If windshield is replaced
| Camera Near Rearview Mirror | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) Behind Front Bumper Cover/Grille
OEM Name: ICC Sensor
Calibration/Initialization Requirement Events:
- After any collision to the front of the vehicle that would cause the radar sensor to be shifted or jolted
- If sensor is removed/installed or replaced
| Sensor(s) Behind Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) Behind Rear Bumper Cover (Sides)
OEM Name: Side Radar
Calibration/Initialization Requirement Events:
- If any blind spot warning system malfunction is repaired
- If sensor is replaced
| Sensor(s) Behind Rear Bumper Cover (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Note:
Not a calibration, but an operation check.
Sensor(s) in Rear Bumper Cover
OEM Name: Sonar Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Rear Bumper Cover | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
| Additional Information | |