OEM Calibration Requirements Search
2019 RAM 1500 (DT)
Click the links below for directions; definitions; articles; and additional RTS portal information such as OEM position statements and publications.
Camera in Deck Lid/Liftgate/Tailgate
OEM Name: Rear View Camera
Calibration/Initialization Requirement Events:
- If camera is removed/installed or replaced
- If central vision processing module is replaced
- If DTC indicates
| Camera in Deck Lid/Liftgate/Tailgate | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Front Bumper Cover/Grille
OEM Name: Front View Camera
Calibration/Initialization Requirement Events:
- If camera is removed/installed or replaced
- If central vision processing module is replaced
- If DTC indicates
| Camera in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Left)
OEM Name: Side View Camera
Calibration/Initialization Requirement Events:
- If camera is removed/installed or replaced
- If central vision processing module is replaced
- If DTC indicates
| Camera in Side Mirror (Left) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Right)
OEM Name: Side View Camera
Calibration/Initialization Requirement Events:
- If camera is removed/installed or replaced
- If central vision processing module is replaced
- If DTC indicates
| Camera in Side Mirror (Right) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera Near Rearview Mirror
OEM Name: Driver Assistance System Module
Calibration/Initialization Requirement Events:
- If drivers assistance system module is removed/installed or replaced
- If DTC indicates
- If tire diameter changes
- If windshield is removed/installed or replaced
| Camera Near Rearview Mirror | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Additional Location(s)
OEM Name: (multiple inputs)
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Additional Location(s) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Note:
Receives input from:
- adaptive front lighting system module (AFLS)
- front and rear axle leveling sensors
- steering angle sensor
- yaw rate sensor
"If this electronic control unit (ECU) is being replaced with a new unit, use a diagnostic scan tool to perform the flash programming procedure (if available)."
Sensor(s) in Front Bumper Cover/Grille
OEM Name: Front Center / Inboard Park Assist Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Front Bumper Cover/Grille (Sides)
OEM Name: Front Outboard Park Assist Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Front Bumper Cover/Grille (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Rear Bumper Cover
OEM Name: Rear Park Assist Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Rear Bumper Cover | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Tail Lamp (Sides)
OEM Name: Blind Spot Sensor
Calibration/Initialization Requirement Events:
- If DTC indicates
- If sensor is removed/installed or replaced
| Sensor(s) in Tail Lamp (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) Near Rearview Mirror
OEM Name: Driver Assistance System Module
Calibration/Initialization Requirement Events:
- If drivers assistance system module is removed/installed or replaced
- If DTC indicates
- If tire diameter changes
- If windshield is removed/installed or replaced
| Sensor(s) Near Rearview Mirror | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
| Additional Information | |