OEM Calibration Requirements Search
2025 Ford Mustang Mach-E
Click the links below for directions; definitions; articles; and additional RTS portal information such as OEM position statements and publications.
Camera in Deck Lid/Liftgate/Tailgate
OEM Name: Rear Parking Aid Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed/installed, replaced, or adjusted
- If DTC indicates
| Camera in Deck Lid/Liftgate/Tailgate | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Front Bumper Cover/Grille
OEM Name: Front Parking Aid Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed/installed, replaced, or adjusted
- If DTC indicates
| Camera in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Left)
OEM Name: Side Parking Aid Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed/installed, replaced, or adjusted
- If DTC indicates
| Camera in Side Mirror (Left) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera in Side Mirror (Right)
OEM Name: Side Parking Aid Camera
Calibration/Initialization Requirement Events:
- If any camera or body component that camera is attached to is removed/installed, replaced, or adjusted
- If DTC indicates
| Camera in Side Mirror (Right) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Camera Near Rearview Mirror
OEM Name: Image Processing Module A Camera
Calibration/Initialization Requirement Events:
- After front airbag deployment
- If camera is removed/installed or replaced
- If DTC indicates
- If suspension is repaired or aligned
- If tire size is changed
- If windshield is removed/installed or replacedD
| Camera Near Rearview Mirror | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) Behind Front Bumper Cover/Grille
OEM Name: Cruise Control Module
Calibration/Initialization Requirement Events:
- If DTC indicates
- If front bumper reinforcement is removed/installed or replaced
- If sensor is removed/installed or replaced
- If sensor mounting bracket is removed/installed or replaced
- If vehicle has been in a collision
| Sensor(s) Behind Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) Behind Front Bumper Cover/Grille (Sides)
OEM Name: Side Obstacle Detection Control Module C/D
Calibration/Initialization Requirement Events:
- If DTC indicates
- If sensor is removed/installed or replaced
| Sensor(s) Behind Front Bumper Cover/Grille (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Additional Location(s)
OEM Name: (multiple inputs)
Calibration/Initialization Requirement Events:
- If DTC indicates
| Sensor(s) in Additional Location(s) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Note:
Receives input from:
- front headlamp leveling sensor
- rear headlamp leveling sensor
- vehicle speed sensor
- steering angle sensor
Sensor(s) in Front Bumper Cover/Grille
OEM Name: Front Parking Aid Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Front Bumper Cover/Grille | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Note:
Per the Ford Workshop manual, operation checks are required. (Azimuth System Check, Elevation System Check)
Sensor(s) in Quarter Panel Behind Bumper Cover (Sides)
OEM Name: Side Obstacle Detection Control Module
Calibration/Initialization Requirement Events:
- If DTC indicates
- If sensor is removed/installed or replaced
| Sensor(s) in Quarter Panel Behind Bumper Cover (Sides) | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Sensor(s) in Rear Bumper Cover
OEM Name: Rear Parking Aid Sensor
Calibration/Initialization Requirement Events:
- No calibration/initialization requirements found
| Sensor(s) in Rear Bumper Cover | Yes | No | Not Identified |
| DTC Set | X | ||
| Scan Tool Required | X | ||
| Special Tools Required | X |
Note:
Per the Ford Workshop manual, operation checks are required. (Azimuth System Check, Elevation System Check)
| Additional Information | |