OEM Restraints System Part Replacement Search


2019 Honda Fit

DISABLE PROCEDURE AND TIME (Always Check Service Manual)

Before disconnecting the SRS unit connectors, always disconnect the appropriate SRS parts connectors.

1. Turn the vehicle to the OFF (LOCK) mode
2. Disconnect the negative cable from the 12 volt battery
3. Wait at least 3 minutes before starting installation or replacement of the SRS unit, or disconnecting the connectors from the SRS unit

REV: 07/2020

PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT

After a collision where the seat belt tensioners deployed, replace these items:
• SRS unit [MODULE,AIRBAG CONTROL]
• Front seat belt(s)
• Front impact sensor(s) [AIRBAG SENSOR,FRONT]

USA and Canada models: After a collision where the driver's seat belt outer lap tensioner deployed, replace these items:
• SRS unit
• Front seat belt(s)
• Front impact sensor(s) [AIRBAG SENSOR,FRONT]

After a collision where the front airbag(s) deployed, replace these items:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed front airbag(s) [AIRBAG,STEERING WHEEL; AIRBAG,INSTRUMENT PNL]
• Front seat belt(s)
• Front impact sensor(s) [AIRBAG SENSOR,FRONT]
• Cable reel (deployed driver's airbag) [CLOCK SPRING]
• Dashboard (deployed front passenger's airbag)

After a collision where the side airbag(s) deployed, replace these items:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed side airbag(s) [AIRBAG,FRONT SEAT]
• Front seat belt(s)
• Side impact sensor(s) (first) [AIRBAG SENSOR,SIDE]
• Side impact sensor(s) (second) [AIRBAG SENSOR,QTR PANEL]
• B-pillar lower trim
• Seat frame and related parts. Replace the seat-back cover/pad if it is damaged.

After a collision where the side curtain airbag deployed, replace the items for the side(s) that deployed:
• SRS unit [MODULE,AIRBAG CONTROL]
• Deployed side curtain airbag(s) [AIRBAG,ROOF]
• Front seat belt(s)
• Side impact sensor(s) (first) [AIRBAG SENSOR,SIDE]
• Side impact sensor(s) (second) [AIRBAG SENSOR,QTR PANEL]
• A-pillar trim
• B-pillar upper trim
• Quarter pillar trim
• Front grab handle
• Rear grab handle
• All related trim clip(s)
• Sunvisor
• Headliner

PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED

• Do not repair damaged SRS wiring. Replace the affected wiring harness(es).
• Before doing any SRS repairs, check for DTCs with the HDS for the less obvious deployed components (front seat belt tensioners, front impact sensors, side impact sensors, etc.).
• USA and Canada models: Do not replace the front passenger's weight sensor unit unless it is physically damaged or a specific fault was found during DTC troubleshooting because it could complicate troubleshooting other DTCs.
• USA and Canada models: After a vehicle collision, do the front passenger's weight sensor unit operation check.
• When replacing the front seat belt tensioner, check the seat belt mounting portion for deformation. If any deformation is found, repair it as needed.
• Check the front passenger's weight sensor output after a vehicle collision
• After a moderate to severe side or rear collision, inspect for any damage on the side curtain airbag or other related components. Replace the components as needed.
• Replace all damaged parts.

Additional Information


*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The following charts were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. To ensure that the most recent information is used, always refer to the vehicle maker's technical information before working with airbags and other passive restraint systems.


Related I-CAR Courses