OEM Restraints System Part Replacement Search
2019 Volkswagen Jetta
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
When working on pyrotechnic components and on the Air-bag Control Module • J234•
1) The battery ground cable must be disconnected with the ignition SWITCHED ON. Then cover the negative pole.
2) Wait for 10 seconds after disconnecting the battery
REV: 02/2023
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
Airbag Units, Removing and Installing After an Accident:Airbag control module must be replaced [MODULE,AIRBAG CONTROL]:
• If the display Control module faulty appears after check-
ing the DTC memory
• With driver and passenger airbag deployment “but not with airbag generation 9.•, 10.• and 8.R
• After three side/ driver/ front passenger airbag or belt tensioner deployments
Always replace the following:
• All deployed airbag units [AIRBAG,STEERING WHEEL, AIRBAG,INSTRUMENT PNL, AIRBAG,FRONT SEAT, AIRBAG,ROOF]
Also with front passenger airbag deployment:
• Instrument Panel
• Deformed supports of the front passenger airbag unit (cannot be reformed)
• All front airbag sensors on the front end [AIRBAG SENSOR,FRONT]
• Remaining transverse acceleration sensors if the mounting
points are deformed in the sensor area [AIRBAG SENSOR,FRT DOOR, AIRBAG SENSOR,QTR PANEL]
Also with driver airbag deployment:
• Return Spring with Slip Ring [CLOCK SPRING/LVR,STRG]
•All front airbag sensors on the front end [AIRBAG SENSOR,FRONT]
• Remaining transverse acceleration sensors if the mounting
points are deformed in the sensor area [AIRBAG SENSOR,FRT DOOR, AIRBAG SENSOR,QTR PANEL]
Also with side airbag deployment:
• Pressure sensors on deployed side [AIRBAG SENSOR,FRT DOOR]
• Transverse acceleration sensors on the deployed side [AIRBAG SENSOR,QTR PANEL]
• Cover
• Cushion
• with a folding rear seat backrest: side cushion (if equipped)
• Remaining transverse acceleration sensors if the mounting
points are deformed in the sensor area
In addition:
• All automatic belt retractors with deployed belt tensioners
• All automatic belt retractors with deployed seat belt force limiters (depending on equipment)
• Seat belt latches for all automatic belt retractors with deployed seat belt tensioners with the belt on
• Seat belt height adjuster (manual and power) for all automatic belt retractors with deployed seat belt tensioners with the belt on
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
• After an accident, all damaged parts must be replaced• After every accident the seat belt system must be inspected systematically
• Connect the Vehicle Diagnostic Tester if there is a chance the belt tensioner and/or seat belt force limiter deployed
The following components must be checked after every airbag deployment.
With a front passenger airbag deployment:
• Instrument panel crossmember; front passenger airbag sup-ports and passenger airbag unit must be installed free of
tension. Otherwise the crossmember is to be replaced.
• Check the glove compartment for damage. Replace the glove compartment if damaged.
With a driver airbag deployment:
• Steering wheel
• Check steering wheel for smoke residue. If smoke residue is present, replace the steering wheel.
Airbag control module must be replaced:
• The airbag control module can be used for up to two deployments of the side, driver and passenger airbag and/or belt tensioner with airbag generation 8.• not 8.R.
• The airbag control module with airbag generation 9.•, 10.• and 8.R. can be used for up to two side, driver and front passenger airbag and/or belt tensioner deployments
• After the third deployment, Control module faulty appears
in the display.
• If housing is damaged
• If there is deformation on tunnel in 200 mm circumference around control module
Also with passenger occupant detection system:
• Each time the front passenger airbag and/or belt tensioner on the front passenger side is deployed, the Passenger Occupant Detection System Control Module • J706• basic setting must be performed using the Vehicle Diagnostic Tester.
• If the seat rail and/or the seat pan are replaced due to defor-mations, then a basic setting must be performed on the Pas-senger Occupant Detection System Control Module • J706using the Vehicle Diagnostic Tester.
If needed (visual inspection), the following must also be replaced: all faulty components.
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The following charts were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. To ensure that the most recent information is used, always refer to the vehicle maker's technical information before working with airbags and other passive restraint systems.
