OEM Restraints System Part Replacement Search
2018 Ford Focus Electric
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
WARNING: Before beginning any service procedure in this section, refer to Safety Warnings in section 100-00 General Information. Failure to follow this instruction may result in serious personal injury.WARNING: To reduce the risk of accidental deployment, do not use any memory saver devices. Failure to follow this instruction may result in serious personal injury or death.
WARNING: Before beginning any service procedure in this section, refer to Safety Warnings in section 100-00 General Information. Failure to follow this instruction may result in serious personal injury
1. Turn all vehicle accessories OFF.
2. Turn the ignition OFF.
3. At the BCM, located on the bulkhead below the glove box, remove the RCM fuse 86 (10A) from the BCM. Refer to Wiring Cell 11 Fuse and Relay Information for schematic and
connector information.
4. Turn the ignition ON and monitor the airbag warning indicator for at least 30 seconds. The airbag warning indicator remains lit continuously (no flashing) if the correct RCM fuse is removed. If the airbag warning indicator is not lit continuously, remove the correct RCM fuse before proceeding.
5. Turn the ignition OFF.
WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury
or death in the event of an accidental deployment
6. Disconnect the battery.
7. Wait at least one minute before continuing vehicle service
NOTE: The airbag warning indicator illuminates when the correct RCM fuse is removed and the ignition is ON.
REV: 04/2018
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
When any deployable device or combination of devices have deployed and/or the RCM has DTC B1193:00 (Event Threshold Exceeded) in memory, the repair of the vehicle SRSis to include the removal of all deployed devices and the installation of new deployable devices, the removal and installation of new impact sensors and the removal and
installation of a new RCM.
all deployed devices:
• Drivers airbag [AIRBAG,STEERING WHEEL]
• Passengers airbag [AIRBAG,INSTRUMENT PNL]
• [AIRBAG,FRONT SEAT]
• Drivers side Safety Canopy [AIRBAG,ROOF] with new J nuts
• Passengers side Safety Canopy [AIRBAG,ROOF] with new J nuts
• When the driver air bag module has deployed, a new clockspring must be installed [CLOCK SPRING]
• A new RCM [MODULE,AIRBAG CONTROL]
• Impact sensors [AIRBAG SENSOR,FRONT; AIRBAG SENSOR,FRT DOOR; AIRBAG SENSOR,QTR PANEL]
• New driver safety belt system (including retractors, buckles and height adjusters) must be installed if the vehicle is involved in a collision that results in deployment of the driver safety belt pretensioners
• New Front passenger safety belt system (including retractors, buckles and height adjusters) must be installed if the vehicle is involved in a collision that results in deployment of the Front passenger safety belt pretensioner
• Install a New headliner and new A-, B-, C• and D-pillar upper trim panels and attaching hardware, if roof airbag deployed
• Install new safety belt(s) at any seating position(s) where deployment has occurred and the safety belt(s) were used.
• New second row safety belt systems (including retractors, buckles and inflators) must be installed if the vehicle is involved in a collision that results in deployment of the rear inflatable safety belt system. [if equipped]
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
Inspect the entire vehicle for damage, including the following components:• Impact sensor mounting points or mounting hardware. When any damage to the impact sensor mounting points or mounting hardware has occurred, repair or install new mounting points and mounting hardware as needed.
• Steering column (deployable column if equipped)
• Instrument panel knee bolsters and mounting points
• Safety Canopy and mounting points
• Instrument panel braces and brackets
• Instrument panel and mounting points
• Seats and seat mounting points
• Safety belts, safety belt buckles, safety belt retractors and safety belt anchors
• SRS wiring, wiring harnesses and connectors
• Before installing the new safety belt assembly, inspect the safety belt attaching areas for damage and distortion. If the attaching points are damaged and distorted, work the sheet metal back to its original shape and structural integrity
When a vehicle has been involved in a collision and the OCSM has DTC B1193:00 stored in memory, the repair of the OCS is to include the following procedures for the
specified system:
• For a bladder-type OCS , inspect for damage and repair as necessary. If installation of an OCS component is required, an OCS service kit must be installed
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The following charts were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. To ensure that the most recent information is used, always refer to the vehicle maker's technical information before working with airbags and other passive restraint systems.
