OEM Restraints System Part Replacement Search
2018 Lexus ES 300h
Share:
|
Print
Print
DISABLE PROCEDURE AND TIME (Always Check Service Manual)
1. Turn engine switch OFF2. Disconnect negative battery cable from the battery
3. Wait at least 90 seconds
REV: 01/2018
PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT
When the SRS parts are deployed (including when only an airbag or pretensioner is deployed) due to a collision, be sure to replace all sensors in the damaged areas (anywhere in need of repair) and airbag sensor assembly (center airbag sensor). [AIRBAG SENSOR,FRONT; AIRBAG SENSOR,FRT DOOR; AIRBAG SENSOR,SIDE; AIRBAG SENSOR,QTR PANEL; MODULE,AIRBAG CONTROL][Replace deployed Airbags]:
• Horn button assembly [AIRBAG,STEERING WHEEL]
• Lower No. 1 instrument panel airbag assembly [AIRBAG,KNEE BOLSTER]
• Lower No. 2 instrument panel airbag assembly [AIRBAG,KNEE BOLSTER]
• Instrument panel passenger airbag assembly [AIRBAG,INSTRUMENT PNL]
• Curtain shield airbag assemblies [AIRBAG,ROOF]
• Front seat airbag assemblies [AIRBAG,FRONT SEAT]
• Rear seat airbag assemblies [AIRBAG,REAR SEAT]
• If the front seat airbag assembly was deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage
• If the rear seat airbag assembly was deployed, replace the rear seat airbag assembly, bench type rear seatback cover and bench type rear seatback pad with the necessary parts in accordance with the extent of the collision damage
PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED
Before using an electric welder on the vehicle, remove any SRS parts around the area being repairedBefore repairs, remove the airbag sensor assemblies if impacts are likely to be applied to the sensor during repairs.
• Horn button assembly [AIRBAG,STEERING WHEEL]
• Lower No. 1 instrument panel airbag assembly [AIRBAG,KNEE BOLSTER]
• Lower No. 2 instrument panel airbag assembly [AIRBAG,KNEE BOLSTER]
• Instrument panel passenger airbag assembly [AIRBAG,INSTRUMENT PNL]
• Curtain shield airbag assemblies [AIRBAG,ROOF]
• Front seat airbag assemblies [AIRBAG,FRONT SEAT]
• Rear seat airbag assemblies [AIRBAG,REAR SEAT]
• Front seat outer belt assemblies
• Rear seat 3 point type outer belt assemblies
• Airbag sensor assembly (center airbag sensor) [MODULE,AIRBAG CONTROL]
• Front airbag sensors [AIRBAG SENSOR,FRONT]
• Door side airbag sensors [AIRBAG SENSOR,FRT DOOR]
• Side airbag sensor assemblies [AIRBAG SENSOR,FRT DOOR; AIRBAG SENSOR,SIDE]
• Rear airbag sensors [AIRBAG SENSOR,QTR PANEL]
• When the airbag sensor assembly (center airbag sensor) is replaced, perform zero point learning for the yaw rate and acceleration sensor
• Visually check the airbag sensors in undamaged areas for defects. If any defects are found or an airbag sensor has detected a major collision, replace the airbag sensor with a new one
| Additional Information |
*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The following charts were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. To ensure that the most recent information is used, always refer to the vehicle maker's technical information before working with airbags and other passive restraint systems.
