OEM Restraints System Part Replacement Search


2018 Nissan 370Z

DISABLE PROCEDURE AND TIME (Always Check Service Manual)

WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance should be performed by an authorized NISSAN/INFINITI dealer.

1. Turn the ignition switch OFF.
2. Disconnect both battery cables.
3. Wait at least 3 minutes.

REV: 06/2017

PARTS THAT MUST BE REPLACED FOLLOWING A DEPLOYMENT

FOR FRONTAL COLLISION:

• If the driver air bag has deployed: REPLACE Install with new fasteners [AIRBAG,STEERING WHEEL]
• If the Passenger front airbag has deployed: REPLACE Install with new fasteners. [AIRBAG,INSTRUMENT PNL]
• If any of the front airbags or seat belt pretensioners have been activated: REPLACE the crash zone sensor and bracket [AIRBAG SENSOR,FRONT]
• Seat belt pre-tensioner assemblies (All applicable locations: buckle, retractor, lap outer), •: Confirm seat belt pre-tensioner activation using CONSULT only.
• If any of the SRS components have been activated: REPLACE the Diagnosis sensor unit [MODULE,AIRBAG CONTROL]
• If the Driver airbag has deployed: REPLACE the spiral cable [CLOCK SPRING]
• If the front passenger air bag has deployed: REPLACE the instrument panel assembly. (integrated type) Always replace instrument panel pad following passenger air bag deployment.
• Always use new fasteners
• Always check the air bag diagnosis sensor unit ECU discriminated number (identification number) using CONSULT.

FOR SIDE AND ROLLOVER COLLISION:

• If the side curtain air bag LH has deployed: REPLACE the side curtain air bag module LH [AIRBAG,ROOF]
• If the side curtain air bag RH has deployed: REPLACE the side curtain air bag module RH [AIRBAG,ROOF]
• If the front side air bag LH has deployed: REPLACE front seatback assembly LH. [AIRBAG,FRONT SEAT and components; AIRBAG & SEATBACK ASSY (Nismo)]
• If the front side air bag RH has deployed: REPLACE front seatback assembly RH. [AIRBAG,FRONT SEAT and components; AIRBAG & SEATBACK ASSY (Nismo)]
• If any of the SRS components have deployed: REPLACE the side air bag (satellite) sensor on the collision [AIRBAG SENSOR,FRT DOOR; AIRBAG SENSOR,SIDE]
• If any of the SRS components have deployed: REPLACE the diagnosis sensor unit [MODULE,AIRBAG CONTROL]
• Seat belt pre-tensioner assemblies (All applicable locations: buckle, retractor, lap outer), •: Confirm seat belt pre-tensioner activation using CONSULT only.
• If the door-mounted curtain air bag module LH has deployed: REPLACE the door finisher LH and door -mounted curtain air bag module [AIRBAG,FRONT DOOR]
• If the door-mounted curtain air bag module RH has deployed: REPLACE the door finisher RH and door -mounted curtain air bag module [AIRBAG,FRONT DOOR]
• When replacing door-mounted curtain air bag module, always replace it together with door finisher as a set.
• If the pop-up roll bar has deployed: REPLACE pop-up roll bar assemblies and pop-up roll bar covers [COVER,ROLL BAR; ROLL BAR ASSEMBLY]
• Always use new fasteners
• Always check the air bag diagnosis sensor unit ECU discriminated number (identification number) using CONSULT.

PARTS THAT MUST BE INSPECTED AND REPLACED IF DAMAGED

Replace any SRS components and the related parts showing visible signs of damage (dents, cracks, deformation).

FOR FRONTAL COLLISION:

• Non-deployed airbags
• Steering wheel
• Occupant classification system
• Harness and connectors
• Seats and seat mounting points
• Instrument panel assembly
• Inspect all seat belt assemblies including retractors and attaching hardware after any collision.

FOR SIDE AND ROLLOVER COLLISION:

• Check for visible signs of damage (dents, tears, deformation) of the center pillar on the collision side. If damaged • Remove the curtain air bag module LH/RH (visual inspect).
• Seats and seat mounting points
• Seat (with side air bag)
• Trim/headliner
• Inspect all seat belt assemblies including retractors and attaching hardware after any collision.
• Satellite sensor (LH or RH)
• After the work is completed, perform self-diagnosis to check that no malfunction is detected

Replace any seat belt assembly (including anchor bolts) if:
• The seat belt is in use at the time of a collision (except for minor collisions and the belts, retractors and buckles show no damage and continue to operate properly).
• The seat belt is damaged in an accident (i.e. torn webbing, bent retractor or guide).
• The seat belt attaching point is damaged in an accident. Inspect the seat belt attaching area for damage or distortion and repair as necessary before installing a new seat belt assembly.
• Anchor bolts are deformed or worn out.
• The front seat belt pre-tensioner must be replaced even if the seat belts are not in use during the collision in which the air bags are deployed

WARNING:
Inspect all seat belt assemblies including retractors and attached hardware after any collision. NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the collision was minor and the belts show no damage and continue to operate properly. Failure to do so could result in serious personal injury in an accident. Seat belt assemblies not in use during a collision should also be replaced if either damage or improper operation is noted. Seat belt pre-tensioners should be replaced even if the seat belts are not in use during a frontal collision in which the air bags are deployed.

Additional Information


*This matrix does not currently contain all production vehicles sold in the United States. Please refer back to this page frequently to ensure the most up-to-date information. The following charts were developed in cooperation with AudaExplore, a Solera company. The contents are based on the information available at the time of publication. To ensure that the most recent information is used, always refer to the vehicle maker's technical information before working with airbags and other passive restraint systems.


Related I-CAR Courses