Repairing Blind Spot Sensor Mounting Locations: Honda/Acura

Submit a new collision repair question here!

Repairing Blind Spot Sensor Mounting Locations: Honda/Acura

As part of the research conducted by the I-CAR RTS team for the OEM Calibration Requirements Search, we have found that some OEMs provide measurements for blind spot sensor mounting locations. When this mounting location information is found, we will publish articles highlighting the information and where to locate it for that specific OEM.

When performing repairs, having measurements is a way to ensure the vehicle is repaired correctly. However, measurements are not always given for body panels. This typically isn’t a problem, until there are advanced driver assistance systems (ADAS) involved, such as blind spot sensors. When mounting blind spot sensors on body panels, it can be crucial to have the mounting location straightened to the correct measurement. Some OEMs not only give measurements but may also provide alternative measuring methods to identify that the sensor is looking in the right direction. Let's see what Honda/Acura has to say.

Honda/Acura has vehicle-specific procedures available to determine the location of the mounting points for the rear blind spot monitoring sensors. This procedure is not a calibration, it is a prerequisite to calibration if needed. The sensor fasteners are installed to a specified depth, then a measurement is taken to determine their location. This procedure is helpful for both straightening and for making sure a replacement quarter panel is positioned correctly.

As ADAS continues to become available and standard on more vehicles, we will continue to research for new information regarding blind spot sensor mounting location measurements. Knowing these specifications and following OEM procedures will help ensure a complete, safe, and quality repair.

For additional Honda/Acura information, check out the following pages:
Honda OEM Information
Acura OEM Information

Additional I-CAR Collision Repair News you may find helpful:
ADAS, Calibration, And Scanning Article Hotspot
Collision Information Website Access: Honda/Acura
Locating ADAS Information: Honda/Acura
Repairing Blind Spot Sensor Mounting Locations
Understanding The Blind Spot Detection System

MIG Brazing What Is It, Why Should I Use It? June 02, 2014
Why MIG Brazing? It is widely known that GMA (MIG) welded; fully galvanized steel will lose some of its properties, including corrosion protection, due to the heat created during welding.…
Toyota/Lexus/Scion Position Statement: Pre- and Post-Repair System Scanning July 28, 2016
As the industry continues to ask if pre- and post-repair system scanning is necessary, Toyota/Lexus/Scion provides their answer.
Typical Calibration Requirements for Blind Spot Sensors October 19, 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system…
Restraints Wiring Repairs May 23, 2016
Over the past few months, we've been sharing OEM position statements on restraints wiring repairs. Now we're bringing them all together in one place for easy reference.
2015 Ford F-150 Outer Box Side Replacement Options August 07, 2015
The method for replacing the outer box side on the 2015 Ford F-150 has been a popular area of discussion, and many people are asking, "What are my options and…
I-CAR Best Practice: Recycled Outer Quarter Panels w/Rolled Hem Flanges July 21, 2017
Periodically, I-CAR Repairability Summits are held to bring together collision industry stakeholders and subject matter experts to develop collision repair processes and best practices for repair of late-model, collision damaged…
Typical Calibration Requirements for Forward Radar Sensors October 12, 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system…
Mazda I-ELOOP Overview January 27, 2014
Beginning model year 2014, Mazda has introduced a regenerative engine braking system called i-ELOOP, short for "Intelligent Energy Loop." In this system, a capacitor is used to store electrical energy…
Typical Calibration Requirements for Park Assist Sensors October 31, 2016
Technicians should be aware of what’s required to keep advanced driver assistance systems (ADAS) running safely after a collision. Whether that be aiming a camera, which can cause a system…
Pre- and Post-Repair System Scanning Position Statements January 09, 2019
Are you wondering if a particular OEM or organization has a published position statement on pre-repair and post-repair scanning? We have compiled a list of most of the position statements…

I-CAR BMW Collision Repair Overview Course September 24, 2020
I-CAR released a collision repair overview course for BMW. This course covers the history of BMW, online service information, construction materials, restraints inspection, advanced driver assistance systems (ADAS), and more
Bumper Cover Repair With ADAS: Subaru September 23, 2020
A simple bumper repair on a modern vehicle may not be as simple as it seems. New technologies like blind spot monitoring, adaptive cruise control, and other advanced driver assistance…
Fiat Chrysler Automobiles (FCA) ADAS Repair Planning: Do You Have All The Information? September 22, 2020
While researching body repair manuals (BRM) and service manuals, we're creating OEM-specific articles for additional information needed when repair planning. The goal of these articles is to help repairers create…
How To Use The OEM Hybrid And Electric Vehicle Disable Search September 17, 2020
The RTS Team has compiled countless hours of research of hybrid and electric vehicles to bring the industry the OEM Hybrid And Electric Vehicle Disable Search page. This search tool…
Hybrid And Electric Vehicle Article Hotspot September 17, 2020
Since hybrid and electric vehicles first started becoming relevant, members of the collision repair industry have required as much knowledge as possible on these subjects. I-CAR’s Repairability Technical Support (RTS)…
Maserati Glass Replacement Requirements September 15, 2020
The role of the windshield is a lot more complex than simply allowing a view of the road ahead. It is considered a structural part of the vehicle as it…
Reading Toyota/Lexus Repair Procedures: It May Take More Than One Procedure September 10, 2020
One of the many functions of the Repairability Technical Support (RTS) team is to assist the collision repair industry with understanding repair procedures. The team often receives questions such as,…
Calibration Research Tips: Hyundai Variant Coding September 09, 2020
While searching for information on advanced driver assistance systems (ADAS) on an OEM repair information site, you may come across unique calibration procedures or events. These events can vary by…
OEM Linking Pin: Honda/Acura - Some New OEM Bumper Covers May Need Special Preparation September 08, 2020
Have you found when scuffing a new Honda/Acura OEM bumper cover that sometimes the coating appears to be as hard as iron? As part of the I-CAR Repairability Technical Support…
Repairer Driven News: 2021 Jeep Wrangler 4xe Plug-In Hybrid September 04, 2020
Repairer Driven News (RDN) released an article on the 2021 Jeep Wrangler 4xe plug-in hybrid which features up to 25 miles of pure electric driving and all power modes available…

2020
- September 2020 (12)
- August 2020 (12)
- July 2020 (19)
- June 2020 (16)
- May 2020 (14)
- April 2020 (21)
- March 2020 (12)
- February 2020 (14)
- January 2020 (14)

2019
- December 2019 (15)
- November 2019 (20)
- October 2019 (25)
- September 2019 (20)
- August 2019 (22)
- July 2019 (23)
- June 2019 (21)
- May 2019 (20)
- April 2019 (21)
- March 2019 (21)
- February 2019 (21)
- January 2019 (19)

2018
- December 2018 (19)
- November 2018 (19)
- October 2018 (17)
- September 2018 (16)
- August 2018 (23)
- July 2018 (21)
- June 2018 (21)
- May 2018 (21)
- April 2018 (20)
- March 2018 (23)
- February 2018 (17)
- January 2018 (21)

2017
- December 2017 (16)
- November 2017 (18)
- October 2017 (19)
- September 2017 (20)
- August 2017 (21)
- July 2017 (19)
- June 2017 (23)
- May 2017 (21)
- April 2017 (16)
- March 2017 (20)
- February 2017 (12)
- January 2017 (13)

2016
- December 2016 (9)
- November 2016 (14)
- October 2016 (21)
- September 2016 (11)
- August 2016 (11)
- July 2016 (9)
- June 2016 (13)
- May 2016 (11)
- April 2016 (12)
- March 2016 (14)
- February 2016 (11)
- January 2016 (7)

2015
- December 2015 (10)
- November 2015 (10)
- October 2015 (13)
- September 2015 (10)
- August 2015 (12)
- July 2015 (11)
- June 2015 (10)
- May 2015 (8)
- April 2015 (10)
- March 2015 (9)
- February 2015 (11)
- January 2015 (12)

2014
- December 2014 (15)
- November 2014 (9)
- October 2014 (12)
- September 2014 (10)
- August 2014 (12)
- July 2014 (14)
- June 2014 (9)
- May 2014 (14)
- April 2014 (10)
- March 2014 (6)
- February 2014 (1)
- January 2014 (28)

Hyundai	Does Hyundai have a sectioning procedure available?
Kia	Does Kia have a sectioning procedure available?
Chevrolet	Does Chevrolet have a warning against sectioning when there is no procedure?
Honda	What does Honda say about repairing damaged airbag system wiring harnesses?
Hyundai	Does Hyundai have part replacement procedures available?
BMW	Can I-CAR send me BMW’s repair procedure?
Honda	What does Honda say about straightening front lower rails?
Subaru	Do you have to replace a front passenger airbag on a Subaru even if the airbag did not deploy? The repair information seems to indicate that it should.
Mercedes-Benz	Can I-CAR send me Mercedes-Benz’ repair procedure?
Nissan	Is there a wiring repair procedure for the airbag connector?

Repairing Blind Spot Sensor Mounting Locations: Honda/Acura

Top Ten Vehicle Specific Questions

Top Ten I-CAR Specific Questions