One-Time-Use Parts And Fasteners: General Motors

Posted on 01 April 2022 Print

What is a one-time-use part, and how do you determine if a fastener, clip, or part can be reused? These are questions that we are confronted with in the collision industry quite a lot. The other big question is "Where do I find this information?"

As the Repairability Technical Support (RTS) team researches OEMs for one-time-use fastener/part information, we are putting together a series of articles on how and where to locate this information for specific OEMs. Let's take a look at General Motors (GM).

When a part or fastener is one-time-use, GM indicates this in Fastener Specifications documents located throughout the vehicle specific body repair manual. In most cases, there is a link to this document in repair pair procedures. GM also uses a yellow icon of the fastener being thrown in the trash.

Per the 2022 Cadillac CT4 service manual, Rear Bumper Fascia Diffuser Replacement procedure: "3. Drill out the 8 rear bumper fascial extension rivets (1). - Left Side and Right Side Remove and DISCARD."

Per the 2022 Chevrolet Tahoe service manual, Rear Suspension Lower Control Arm Replacement procedure: "Note: The rear lower control arm adjust cam retainer (1) is for factory alignment purposes only and should NOT be reused."

Following OEM procedures, including the identification and use of one-time-use fasteners/parts, is important in order to help ensure a complete, safe, and quality repair.

Additional I-CAR Collision Repair News you may find helpful:

Related I-CAR Courses

Course General Motors (GM) Company Collision Repair Overview

Course Trim Removal and Installation

  • OEM Emergency Response Guide: Polestar Thursday, 31 October 2024

    Are you looking for OEM emergency response guides (ERGs)? The Repairability Technical Support (RTS) team has located these guides and either houses them on the RTS website, provides links to...

  • Back-To-Basics: Stationary Glass Installation Considerations Wednesday, 30 October 2024

    Sometimes going back-to-basics can make the difference between a quality repair and a failed repair. When replacing stationary glass there are extra considerations to perform a complete and quality...

  • One-Time-Use Parts And Fasteners: Genesis Friday, 25 October 2024

    What is a one-time-use part, and how do you determine if a fastener, clip, or part can be reused? These are questions that we are confronted with in the collision industry quite a lot. The other big...

  • OEM Linking Pin: Toyota/Lexus Sectioning Clarification Thursday, 24 October 2024

    As part of the I-CAR Repairability Technical Support (RTS) OEM linking pin activity, we are helping to connect the collision repair industry to the vehicle makers. A common question when it comes to...

  • Refinishing Park Assist Sensors: Jaguar Land Rover Tuesday, 22 October 2024

    Park assist sensors are part of the park assist system, just one of many advanced driver assistance systems (ADAS) found on vehicles today. Damaged sensors are typically replaced and may require...

  • I-CAR At SEMA 2024 Friday, 18 October 2024

    Attending the SEMA Show in Las Vegas this year? Well, I-CAR will be providing many different opportunities to connect with you at this year’s show.

  • Non-SRS Wiring Repair: BMW/Mini Thursday, 17 October 2024

    What is a non-SRS wiring repair? It is the repairing of an electrical component that is not part of the supplemental restraints system circuit (usually identified by yellow wire looms). As...

  • Paint Maker ADAS Radar Optimized Color Resources: BASF Wednesday, 16 October 2024

    Changes in advanced driver assistance systems (ADAS) radar technology are introducing new refinishing considerations. We know that paint film thickness can affect the performance of ADAS radars, but...

  • Repairer Driven News: BMW Adds Structural Steel Parts To Restricted List Thursday, 10 October 2024

    Repairer Driven News (RDN) has released an article highlighting BMW adding structural steel parts to their restricted list.

  • Ford On Target 2024: Volume 3 Wednesday, 9 October 2024

    Ford has released the third installment of their On Target publication for 2024.