Audi: Who Requires Or Recommends MIG Brazing?

Posted on 17 March 2021 Print

In Europe, MIG brazing has been required or recommended on a widespread basis for several years. In the U.S., MIG brazing is not as common but is becoming more prevalent. As the RTS team is researching MIG brazing information, we are putting together a series of articles that identify OEM-specific MIG brazing recommendations and requirements for vehicles in the U.S. Let’s see what Audi has to say.

Welding general information is located in the Body Repair, Body Collision Repair manual. Here you can find a Replacement Joining Procedures chart that explains what types of welds should be used to replace factory welds.

For example, the manual specifies that where "laser soldering" is used on steel in production, "MIG soldering" (brazing) is not approved for Audi AG vehicles. The Body Repair, Body Collision Repair manual also states that MIG brazing is not used in the repair of aluminum parts which were brazed from factory. The chart also specifies to pay attention to welding information in the vehicle-specific repair manuals.

It is important to note that MIG brazing should only be used where indicated in a vehicle-specific repair manual or where specified by the OEM to help ensure a complete, safe, and quality repair.

For additional Audi information, check out the Audi OEM Information page.

Additional I-CAR Collision Repair News you may find helpful:

Related I-CAR Courses

Course Introduction to MIG Brazing

Course MIG Brazing Hands-On Skills Development

  • OEM Emergency Response Guide: Polestar Thursday, 31 October 2024

    Are you looking for OEM emergency response guides (ERGs)? The Repairability Technical Support (RTS) team has located these guides and either houses them on the RTS website, provides links to...

  • Back-To-Basics: Stationary Glass Installation Considerations Wednesday, 30 October 2024

    Sometimes going back-to-basics can make the difference between a quality repair and a failed repair. When replacing stationary glass there are extra considerations to perform a complete and quality...

  • One-Time-Use Parts And Fasteners: Genesis Friday, 25 October 2024

    What is a one-time-use part, and how do you determine if a fastener, clip, or part can be reused? These are questions that we are confronted with in the collision industry quite a lot. The other big...

  • OEM Linking Pin: Toyota/Lexus Sectioning Clarification Thursday, 24 October 2024

    As part of the I-CAR Repairability Technical Support (RTS) OEM linking pin activity, we are helping to connect the collision repair industry to the vehicle makers. A common question when it comes to...

  • Refinishing Park Assist Sensors: Jaguar Land Rover Tuesday, 22 October 2024

    Park assist sensors are part of the park assist system, just one of many advanced driver assistance systems (ADAS) found on vehicles today. Damaged sensors are typically replaced and may require...

  • I-CAR At SEMA 2024 Friday, 18 October 2024

    Attending the SEMA Show in Las Vegas this year? Well, I-CAR will be providing many different opportunities to connect with you at this year’s show.

  • Non-SRS Wiring Repair: BMW/Mini Thursday, 17 October 2024

    What is a non-SRS wiring repair? It is the repairing of an electrical component that is not part of the supplemental restraints system circuit (usually identified by yellow wire looms). As...

  • Paint Maker ADAS Radar Optimized Color Resources: BASF Wednesday, 16 October 2024

    Changes in advanced driver assistance systems (ADAS) radar technology are introducing new refinishing considerations. We know that paint film thickness can affect the performance of ADAS radars, but...

  • Repairer Driven News: BMW Adds Structural Steel Parts To Restricted List Thursday, 10 October 2024

    Repairer Driven News (RDN) has released an article highlighting BMW adding structural steel parts to their restricted list.

  • Ford On Target 2024: Volume 3 Wednesday, 9 October 2024

    Ford has released the third installment of their On Target publication for 2024.