Honda/Acura: Additional High-Strength-Steel Welding Wire Approved

The Honda/Acura high-strength-steel welding wire has seen several changes in the past few years. The biggest change was going from Bosch DS980J to Bohler Union X96 welding wire. To answer the increased demand for the welding wire, Honda/Acura has expanded their list of welding wire types and suppliers.

Along with the Bohler Union X96 through Pro Spot and Honda Snap-on, Honda/Acura has added Titan Technology EQ-5029X96 and Washing Alloy Eagle-Arc 980X to their welding wire product line. Per the recent Honda Body Repair News: Additional High-Strength-Steel Welding Wire and Acura Body Repair News: Additional High-Strength-Steel Welding Wire , “All three options have a wire size of 0.8 mm (0.030 inch) in diameter and are used for welding joints in high-strength-steel of 590 MPa and higher. You can also use them for welding lower grade steel but are not necessary to provide the required strength.”

Just a reminder that even though the Bosch DS980J has been discontinued, the wire can still be used. It is also important to note that the wire can only be used on 1,500 MPa where directed by the vehicle-specific OEM procedure.

For additional Honda/Acura information, check out the following pages:
Honda OEM Information
Acura OEM Information

Additional I-CAR Collision Repair News you may find helpful:


Related I-CAR Courses

  • OEM Emergency Response Guide: Polestar Thursday, 31 October 2024

    Are you looking for OEM emergency response guides (ERGs)? The Repairability Technical Support (RTS) team has located these guides and either houses them on the RTS website, provides links to...

  • Back-To-Basics: Stationary Glass Installation Considerations Wednesday, 30 October 2024

    Sometimes going back-to-basics can make the difference between a quality repair and a failed repair. When replacing stationary glass there are extra considerations to perform a complete and quality...

  • One-Time-Use Parts And Fasteners: Genesis Friday, 25 October 2024

    What is a one-time-use part, and how do you determine if a fastener, clip, or part can be reused? These are questions that we are confronted with in the collision industry quite a lot. The other big...

  • OEM Linking Pin: Toyota/Lexus Sectioning Clarification Thursday, 24 October 2024

    As part of the I-CAR Repairability Technical Support (RTS) OEM linking pin activity, we are helping to connect the collision repair industry to the vehicle makers. A common question when it comes to...

  • Refinishing Park Assist Sensors: Jaguar Land Rover Tuesday, 22 October 2024

    Park assist sensors are part of the park assist system, just one of many advanced driver assistance systems (ADAS) found on vehicles today. Damaged sensors are typically replaced and may require...

  • I-CAR At SEMA 2024 Friday, 18 October 2024

    Attending the SEMA Show in Las Vegas this year? Well, I-CAR will be providing many different opportunities to connect with you at this year’s show.

  • Non-SRS Wiring Repair: BMW/Mini Thursday, 17 October 2024

    What is a non-SRS wiring repair? It is the repairing of an electrical component that is not part of the supplemental restraints system circuit (usually identified by yellow wire looms). As...

  • Paint Maker ADAS Radar Optimized Color Resources: BASF Wednesday, 16 October 2024

    Changes in advanced driver assistance systems (ADAS) radar technology are introducing new refinishing considerations. We know that paint film thickness can affect the performance of ADAS radars, but...

  • Repairer Driven News: BMW Adds Structural Steel Parts To Restricted List Thursday, 10 October 2024

    Repairer Driven News (RDN) has released an article highlighting BMW adding structural steel parts to their restricted list.

  • Ford On Target 2024: Volume 3 Wednesday, 9 October 2024

    Ford has released the third installment of their On Target publication for 2024.